Conair GS95 Instructions d'exploitation télécharger pdf

6. With telescopic pole now fully assembled,

place the T-Nozzle onto holder above the

hanger.

7. When you are ready to steam, fill the water

tank from the top opening. Note, do not open

the bottom cap as this is used for cleaning or

removing excess water only.

8. Plug the steamer unit into a standard 120V

AC power outlet.

9. The bristle brush attachment easily

snaps over the T-nozzle for use. To use the

creaser attachment, simply line up at base

and slide into back under T-nozzle and push

firmly to attach. See instruction booklet

"Attachments" section figures 5 and 6

for more details.

TURNING STEAMER ON

1. Push the On/Off switch on

base of unit to On – red light

will go on (A).

2. The unit will heat up in

approximately 100 seconds

and will be ready to use when

green light is on (B).

3. Push button on T-nozzle –

light will go on and steam

will start. Button on T-nozzle

can be used On or as a Pause

feature.

Always hold the nozzle about ½ inch from

fabric while steaming.

IMPORTANT SAFETY

INSTRUCTIONS

When using electrical appliances, espe-

cially when children are present, basic

safety precautions should always be taken,

including the following:

READ ALL INSTRUCTIONS

BEFORE USING

DANGER – Any appliance is electri-

cally live even when the switch is off.

To reduce the risk of death by electric shock:

1. Always unplug appliance immediately

after using.

2. Do not place or store appliance where it

can fall or be pulled into a tub or sink.

3. Do not place in, or drop into water or

other liquids.

4. If an appliance falls into water, unplug it

immediately. Do not reach into the water.

WARNING –

To reduce the risk of

burns,

electrocution, fire, or injury to persons:

1. This appliance should never be left

unattended when plugged in.

2. This appliance should not be used by, on,

or near children or individuals with certain

disabilities. Unsupervised use could result in

fire or personal injury.

3. Use this appliance only for its intended

use as described in this manual. Do not

use attachments not recommended by the

manufacturer.

4. Never operate this appliance if it has a

damaged cord or plug, if it is not work-

ing properly, or if it has been dropped or

damaged, or dropped into water. Do not

attempt to repair the appliance. Incorrect

reassembly or repair could cause a risk

of fire, electric shock, or injury to persons

when the appliance is used. Return the

appliance to an authorized service center

for examination and repair.

5. Keep the cord away from heated surfaces.

Do not allow cord to touch heated surfaces.

Do not pull or twist cord. Let appliance cool

completely before putting away.

6. To reduce the risk of electric shock, this

appliance has a polarized plug (one blade

is wider than the other). This plug will fit in

a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a qualified

electrician to install the proper outlet. Do not

change the plug in any way.

7. Never drop or insert any object into any

opening

or hose.

8. Do not use outdoors or operate where

aerosol (spray) products are being used or

where oxygen is being administered.

9. Do not use an extension cord to operate

appliance.

10. Surfaces of this appliance may be hot

when in use. Do not let heated surfaces

touch eyes or skin.

11. Do not place the steam nozzle directly on

any surface or on the appliance power cord

while it is hot or plugged in. Use the stand

provided.

12. Unplug this appliance before filling or

emptying. Do not overfill.

13. While emitting steam, this appliance may

cause burns if it is used too close to the skin,

scalp or eyes, or if it is used incorrectly. To

reduce the risk of contact with hot water

discharging from steam vents, test appliance

before each use by holding it away from body.

14. Do not operate steamer without properly

filling the water tank.

15. Always keep the hose and nozzle

elevated above the water tank.

16. Never yank cord to disconnect from

outlet. Instead, grasp plug and pull to

disconnect.

17. Burns could occur from touching hot

metal parts, hot water, or steam. Use care

when removing water tank or when you turn

a steam appliance upside down – there may

be hot water in reservoir.

18. To reduce likelihood of circuit overload,

do not operate another high-wattage appli-

ance on the same circuit.

19. If an extension cord is absolutely

necessary, a 15 ampere rated cord should

used. Cords rated for less amperage may

overheat. Care should be taken to arrange

the cord so that it cannot be pulled or

tripped over.

20. Always remove the water tank from the

appliance before filling it with water.

21. When changing attachments, please be

sure the unit is off and no steam is being

released in order to avoid contact with hot

water.

22. Use caution when changing attachments,

as there may be hot water from condensation.

Ensure the attachments are dry or cooled off,

to avoid contact with hot water.

SAVE THESE

INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

UNPACKING INSTRUCTIONS

Place the box on a large, sturdy flat surface.

Carefully remove the appliance from the

packing material. Keep all plastic bags away

from children.

STEAMER ASSEMBLY

Attaching the Telescopic Pole and

Rotating Hanger

1. Turn the lock on top of base unit to unlock

position and place telescopic pole into open-

ing. Turn clockwise to lock.

2. Fully extend the telescopic pole, making

sure to lock the pole upright by engaging

the two clips, and hang the steam nozzle

from the cradle atop the 360 degree rotating

hanger assembly.

3. Pull lower pants clips towards you and

rotate clockwise to lock into place.

4. This unit comes with a rotating hanger. To

use the hanger, simply place on top of pole

firmly. Then tighten lower nut to keep hanger

upright or untighten to collapse hanger. It

is now in place to rotate 360˚. Hang your

garment and steam away wrinkles. Turn as

you wish.

5. Attach the top pants clip bar to the rotat-

ing hanger by inserting mounting pegs into

the hanger’s two keyhole openings. Push in

and pull down to lock. See instruction

booklet "Using pant clip system", Fig.3

for more details.

OPERATING

INSTRUCTIONS

FILLING THE WATER TANK

(PRIOR TO PLUGGING IN THE APPLIANCE)

Remove the water tank using

handle on front of tank. Fill

reservoir using opening on top

of tank by holding it under a

source of cold running water

until

it is filled to the desired

level. Do not overfill. Position the water tank

on the base and make certain it is seated

properly in the unit.

DO NOT FILL THE TANK WITH HOT WATER.

DISTILLED OR FILTERED WATER IS BEST.

Do not unscrew the bottom

cap unless for cleaning (Fig. 4).

Note, be sure always empty or

fill the tank over a sink, being

careful not to spill water from

the top of the tank.

GET TO KNOW YOUR STEAMER

USING PANT CLIP SYSTEM

This fabric steamer is equipped with a pant

clip system for holding pants taut for faster

and more effective steaming.

Attach the top pants clip bar to the rotating

hanger by inserting mounting pegs into the

hanger’s two keyhole openings (Fig. 3).

Push in and pull down to

lock (as highlighted above).

The bottom clips can be

adjusted by loosening the

knob (on the telescopic

pole) and moving the pole

up and down, depending

upon the length of pants.

Clip pants as shown and

steam. Please note: some

pants may be too long to

use the bottom clips. If

that is the case, just sim-

ply use the top clips and

let your pants hang freely.

cool-touch

insulated hose

360˚ rotating,

collapsible

hanger

Clips for

steaming

pants

Main On/Off

switch

(red light)

Ready to use

indicator light

(green light)

T-nozzle On/Off

button for steam

Telescoping

pole for height

adjustment

TOP

Steam nozzle with

aluminum faceplate

Removable,

easy-to-fill

large capacity

water tank

2 large

diameter

casters

(Fig. 1)

(Fig. 2)

(Fig. 3)

BOTTOM

(Fig. 4)

Bristle brush attachment

Creaser Attachment

ATTACHMENTS

The bristle brush attachment easily snaps

over the T-nozzle as shown below (Fig. 5).

For the creaser attachment, simply line up at

base and slide into back under T-nozzle and

push firmly to attach as shown below (Fig. 6).

Make sure your steamer is off and has cooled

before adding or removing attachments.

(Fig. 5)

(Fig. 6)

gs95_13pa140688_ib_final.indd 1 3/1/13 3:11 PM

1 2

Résumé du contenu

Page 1 - OPERATING

6. With telescopic pole now fully assembled, place the T-Nozzle onto holder above the hanger.7. When you are ready to steam, fill the water tank from

Page 2 - FABRIC STEAMER

TROUBLESHOOTING THE STEAMER• PROBLEM - Steamer fails to heat CAUSE - Steamer not plugged in SOLUTION - Plug into electrical outlet• PROBLEM - No ste

Commentaires sur ces manuels

Pas de commentaire

Conair GS95 Instructions d'exploitation

Naviguer en ligne ou télécharger Instructions d'exploitation pour Nettoyeurs à vapeur pour vêtements Conair GS95. Conair GS95 Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Nettoyeurs à vapeur pour vêtements Conair GS95